For extended use, we suggest replacing this with an alkaline battery. For extended use, we suggest replacing this with an alkaline battery. Turning the knob clockwise lengthens the delay time. For information on cable specifications, contact the manufacturer of the cable. Setting the minimum value is not possible. Advertisement Print version Many people prefer to read the documents not on the screen, but in the printed version.
. These sections provide important information concerning the proper operation of the unit. When powering up: Turn on the power to your guitar amp last. Owner's Manual Boss Software License Agreement In no event shall Boss Corporation be liable to end-users for any damages whatsoever, including but not limited to financial damages for any loss of profits or information arising from the use of, or inability to use this updater. For extended use, we suggest replacing it with an alkaline battery. Thumbscrew When this screw is loosened, the pedal will open, allowing you to change the battery.
Turn on the effect After you have finished making the connections p. Mode Sticker: This allows you to check the function of each mode. Adjust the volume Use the E. Using the Tempo Delay The delay sound produced is as shown in the figure. When recording is finished, playback starts Press the built-inpedal switch a second time to stop recording. It does not indicate whether the power to the device is on or not.
After the settings have been saved, the unit returns to normal operation. Application Sticker: This allows you to check the difference in functions according to the input and output connections. Adjust the delay time Adjust the delay time with the D. Connect the snap cord to the new battery, and place the battery inside the battery housing. You can keep the recorded content playing continuously as backing and produce other special effects. However, there is no guarantee that interference will not occur in a particular installation. Replace the battery following the steps below.
A brief interval a few seconds after power up is required before the unit will operate normally. Adjust the feedback level Use the F. Trick Sound Employs repetitions of delayed sound to create an oscillating sound. Replace with a new battery p. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, this manual should be read in its entirety. The number of times the delay sound is repeated increases as the knob is turned to the right. Adjust the volume Adjust the volume level of the effect sound with the E.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation. Setting the Tempo Using the Built-inPedal 1. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. Room Ambience Sound This delay simulates the sound that would be picked up by an ambience mic located on a stand within the room. Check the connection once more p.
Overdubbing can also layer this as you perform something Press the pedal switch during playback to else, then record these together overdub. Unique effects can be obtained by adjusting the D. Hold down the pedal and loosen the When the indicator goes dim or no longer thumbscrew, then open the pedal lights while the effect is on, it means that the upward. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. Pedal Switch This is used for switching the effect on and off, and for switching between the different functions p. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual.
Use a connection cable that does not con- When the indicator goes dim or no longer tain a resistor. Check the settings of the connected device. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Unauthorized changes or modification to this system can void the users authority to operate this equipment. Finally, insert the thumbscrew into the guide bush hole and fasten it securely.
These sections provide important in- formation concerning the proper operation of the unit. It does not indicate whether the power to the device is on or not. Check the connection once more p. Thumbscrew Pedal Spring Base Battery Snap Cord Coil Spring Guide Bush Hole Battery Snap Battery Housing 9V Battery 1. Each mode provides a different type for stereo delay. Each mode provides a different type of stereo delay effect. The life of this battery may be limited, however, since its primary purpose was to enable testing.