Hyosung gt125 owners manual. Hyosung Gt125 Workshop Manual PDF Online Free 2019-03-25

Hyosung gt125 owners manual Rating: 9,5/10 1289 reviews

Hyosung GT125 & GT250 Workshop Manual

hyosung gt125 owners manual

If turning itcounter-clockwise , it may cause damage. Install the clutch release arm as following:Turn the clutch release shaft toward This time, mark on the shaft align outside contact line the stopper screw the right. Data beside it indicates specified torque. Do not allow dirt and fluid to contact the brake disc or pad. If any abnormal condition is noted, replace the caliper. Sting had contradicted below the inexorably overdue valeri.

Next

Hyosung GT125 & GT250 Workshop Manual

hyosung gt125 owners manual

Close the air bleeder valve, and disconnect the hose. Swingarm pivot nut: 45~70 Nm 4. Refer to page 6-7 Remove the front fork after loosening the front forkupper and lower clamp bolts. The classification is Ffor the front andRforthe rear. Install the cam guide and pawl lifter. Add distilled water, if the battery has not been damaged and sulfationhas not advanced too far, and recharge.

Next

Hyosung GT125 Comet & GT125R (up to 2009) Specifications

hyosung gt125 owners manual

Check the fuel flow when starting the engine for few seconds by pressing the starter switch. Inspect the rear cylinder's valve clearance with thesame manner of the front cylinder. Disconnect the clutch cable end out of clutch release arm. If the clearance checked is noted to exceed the limit specified, replace the fork or its gear, or both. Pull down right and left front forks. If the valve clearance is within standard after measured the valve clearance, begin the next operation. I f t he l ar gest r eadi ng at any posi t i on of t hestraightedge exceeds the limit, replace the cylin-der.

Next

Hyosung GT125 & GT250 Workshop Manual

hyosung gt125 owners manual

Inspect IntervalClean Initial 1,000 km and Every 4,000 km, Replace Every 8,000 km. Check the valve springs for proper strength by measuring their free length and also by the force requiredto compress them. After cleaning, reinstall the pilot screw to the original number of turn that is recorded during disassembly. Special tools Part NumberPart NameDescription09900-20201Micrometer 0~25mm Used for precise measurement 00~25mm measure ranges. Overtight steering pre-vents smooth turning of the handlebars and too loose steering will cause poor stability. An excessive amount of runout is usually due to worn or loose wheel bearings and can be corrected by replacing the bearings.

Next

Hyosung Gt125 Workshop Manual PDF Online Free

hyosung gt125 owners manual

Raise the front wheel off the ground with a blockor jack. Measure the float height while the float arm is just contacting the needle valve using vernier calipers. When it is necessary to run the engine indoors, make sure that exhaust gas is forced outdoors. There are also other fancy online books in our websites that can be easy to be got looks like it. Be careful not to allow water to go inside the air clea-ner element.

Next

Hyosung Gt125 Owners Manual PDF Online Free

hyosung gt125 owners manual

Do not reuse the piston seal and dust seal that have been removed. Therefore, ahigh voltage current is induced in the secondary winding of the ignition coil and results in strong spark between spark pluggap. Replace the battery, if badlysulfated. Tighten the caliper mounting bolts. C Valve timing diagramValve head thickness Service limit 0.

Next

SOLVED: Owners manual for a Hyosung gt125r

hyosung gt125 owners manual

No fuel reaching the carburetor1. If the spring length is less than theservice limit or if the force required to compress thespring does not fall within the specified range, replaceboth the inner and outer springs as a set. Oil fil-ter repl acement at the above i nterval s, shoul d be together with the engine oil change. Good luck and have a wonderful day. Measure the shim thickness at present. Use of incrrect engine oil. The ignition coils will send voltage to the spark plugs dependant on what gear the transmission is in and whe-ther the side stand is either up or down.

Next

manual moto hyosung cruiser 125

hyosung gt125 owners manual

Remove the pilot screw with count and tighten thenumber of turn. Never use gasoline as a cleaning solvent. Starkers postures were molting in the venally random polyphony. Do not allow dirt and fluid to contact the brake disc or pad. Remove the piston pin circlips with long-nose pliers.

Next

Hyosung GT125 Comet & GT125R (up to 2009) Specifications

hyosung gt125 owners manual

Install the front fork to the motocycle. The removed O-ring should be replacedwith a new one. The presence of air is indicated by sponginessof the brake lever and also by lack of braking force. If any one of the measurements exceeds the limit, overhaul the cylinder and replace the piston with an oversize, or replace the cylinder. Remove in the order of spacer , shaft , starter idle gear.

Next