We offer bucket truck parts and accessories as well as digger derrick parts from over 30 manufacturers so whatever your needs we can help. Tried lowering the pressure to 500, but no results with remote operation. Hello everyone; I'm a fairly new hydraulic technician. Now, when I cleaned the remote, I found that every supply line in the supply manifold had an orifice in it - so I cleaned each one using small files normally used to clean blow torch tips. We stand by our service motto — Prompt, Responsive Service … Guaranteed Every Day. Beat the competition and improve your efficiency with a Pengo auger from Utility Equipment Parts. Double Esterlon Bucket Truck Winch Rope The Double Esterlon winch rope is a double-braided winch rope designed for utility trucks and constructed of high tenacity 1W81 polyester fiber which has a unique cordage finish.
The individual components are easily assembled at the pole removal site. The leaks were not as bad as I made them seem I guess. That was a chore and a half talk about leaking oil! The axles incorporate machined kingpins with bronze bushings and are equipped with grease fittings. Working Heights range from: 33. Each stanchion is equipped with an over-center, variable tension, cam-lock assembly that locks into position using its large handle lever, and is completely adjustable to fit various sizes of channel type or I-beam bolsters. Utility Equipment Parts can also get you the little tools and accessories that make a big difference in utility work — bucket covers, aerial aprons, tool buckets, winch ropes, tow ropes, hooks, stanchions and more! Tiiger Pole Dolly Tiiger Pole Dolly The Tiiger Pole Dolly allows the pole to be easily moved by two people — one person steering the dolly and the second holding and guiding one end of the pole. Tiiger Cube Tiiger Cube The Tiiger Cube is a compact gas-powered single stage hydraulic pump designed for use in remote or confined spaces.
They provide a solid foundation for your equipment, reduce the chance of vehicle tip-over, and reduce the possibility of ergonomic injuries to operators. Next step is to repair the unloading valve - then we should be ready to fill with the proper synthetic. What model Hi-Ranger are you working on? I'll try and get a photo of the nut directly, right now all I have is a photo of the lower side of the remote so I would know which tubes go where for reinstall. The Tiiger Cube is specially designed for the Tiiger Pole Puller and is simple to operate. These carbide augers are built to drill through rocky, abrasive soil with ease.
Do you have the correct gauge to read the nitrogen pressure in the accumulator when you move the booms? It might take a while to show up, but it will show up, and will be very expensive to fix. The heart of the system is the lightweight hydraulic cylinder with a lift capacity exceeding 50,000 pounds. Polyethylene maintains resistance in sub-zero temperatures as low as -130 F. The reason I am feeding at 1000psi is because that was the pressure when I received the truck. Terex Hi-Ranger Articulating Telescopic Aerial Devices Whether you're replacing an insulator, a crossarm, or a cable line, we have the equipment you need in a multitude of configurations.
The sections below show you information about some of our most popular bucket truck parts and accessories. The locking dog assembly holds the anchor rod in place. Initially before I installed new orifices, I was finding that all flow to the remote came down the return line immediately. I started a new thread but didnt get any replies on it so thought I would come back to this post. We have a wide selection of high quality, abrasion-resistant ropes for the utility industry. His fluid is getting really hot.
Double esterlon has an average strength of 9. Lifting a 45-foot pole and placing it on Tiiger Pole Dolly and then moving it in any direction is accomplished by positioning the pole in the roller cradle at the balance point of the pole. I installed new orifices, and can sometimes get enough pressure on the lower boom to somewhat shift the spool - usually see about 25psi out of the handle with 1000 psi in. Weighing in at only 57 pounds, it still provides a lifting capacity greater than or equal to other pole pullers. Set the on-off switch to on and open the fuel line switch, set the choke and throttle, pull the recoil starter and off you go! It is designed with the unique round centering bar for proper placement of the cylinder and uniform distribution of the downward load. .
Two handles make for an ergonomic design resulting in low handling stress for the operator. The easy-to-maneuver Tiiger pole pullers, load dock, and dolly have been engineered and manufactured with specific utility applications in mind. We have been in business for over 8 years, and we will get you the parts you need quickly. What proceedure did you use for bleeding the upper control? I filed at them so much, that I changed their size. The combination of the pad and base plate provides the lowest possible center of gravity and minimizes the potential for the cylinder to tip.
Utility workers appreciate the bucket truck parts and accessories supplied by Utility Equipment Parts, because they make utility work. Screw Anchor Wrenches and Accessories Utility Equipment Parts offers parts to assemble your screw anchor wrench — Kelly bar adapter, locking dog assembly, and drive end. There are a number of ways of fixing a malfunctioning upper control valve. I'm trying to repair a friends truck He's the Deacon at Church - uses the truck for a living. All the working parts of the valve would be replaced. Plus, the liners weigh when made from Polyethylene. When I started off, it was obvious that the system had not been maintained since it was purchased.
The 2 Safe bucket liner features two different colors. Skydrol is not compatible with seals used in petroleum hydraulic systems, and vice versa. The pole roller cradle is constructed with high strength steel and equipped with high molecular weight polyethylene rollers. Over time, if the 2 safe bucket liner becomes worn or damaged on one side you will see the other color on this side. Utility Equipment Parts is your best source for all screw anchor wrenches and other bucket truck parts and accessories. Chris Truck has an accumulator tank nitrogen tank and is cycling the pump on and off without problem. We're not getting foaming in the pressure lines up to the remote.