Mitsubishi servo drive manual. MITSUBISHI ELECTRIC MELSERVO MR 2019-01-25

Mitsubishi servo drive manual Rating: 6,4/10 1518 reviews

Mitsubishi Servo Motor Repair

mitsubishi servo drive manual

Servo amplifier terminals are used to reduce the required wiring time. The symbols in the control mode column of the table indicate the following modes: P : Position control mode S : Speed control mode. Internal speed command 3 Used to set speed 3 of internal speed commands. Detail Detail name Cause Check method Check result Action Target 7A. Or the Check if the trouble is solved Adjust gains. Name Symbol Cumulative feedback pulses Servo motor speed Droop pulses Cumulative command pulses Command pulse frequency Analog speed.

Next

MITSUBISHI ELECTRIC MELSERVO MR

mitsubishi servo drive manual

Otherwise, it may cause an accident. Use the following surge absorber or equivalent. Refer to this section and connect the interfaces with the external equipment. Pin name and name are from the manuals for the control and service manuals for reference use. Thank you for your time. Alarm content The voltage of the main circuit power supply has dropped. Alarm content A diagnosis of input devices was not executed.

Next

MITSUBISHI ELECTRIC MELSERVO MR

mitsubishi servo drive manual

Always make connection for use in an absolute position detection system. To use the equipment correctly, do not attempt to install, operate, maintain, or inspect the equipment until you have read through this Instruction Manual, Installation guide, and appended documents carefully. Detail Detail name Cause Check method Check result Action Target 16. Use the servo amplifier drive unit and converter unit with the specified servo motor. Detail Detail name Cause Check method Check result Action Target 50. Detail Detail name Cause Check method Check result Action Target E2. Need not be connected for the data set type home position return.

Next

AC Servos

mitsubishi servo drive manual

If there is a possibility that the load inertia moment may exceed the value, contact Mitsubishi. Ventilation ports are provided in both side faces and top face. Otherwise, you may get an electric shock. Detail Detail name Cause Check method Check result Action Target 68. The following table lists comparison of the response level setting. At the same point as you - trying to sort out logic on the same connector.

Next

MITSUBISHI ELECTRIC Global website

mitsubishi servo drive manual

Detail Detail name Cause Check method Check result Action Target 20. If communication is interrupted for longer than 0. Display examples are shown below. . Select operation after home position the range of specifications. Symbol Internal speed command 5 Used to set speed 5 of internal speed commands.

Next

AC Servos

mitsubishi servo drive manual

The cables longer than 5m 16. Each axis: Only alarming axis will stop. Detail Detail name Cause Check method Check result Action Target 51. The window shown in the right hand image will be displayed. Combination of servo amplifier and servo motor The servo amplifier software versions compatible with the servo motors are indicated in the parentheses.

Next

AC Servos

mitsubishi servo drive manual

Create a program for the third axis in a similar manner. The servo amplifier and servo motor may become faulty. Insulate the wiring as shown in the diagram. The ability to obtain original technical data sheets allows us to make effective repairs. Detail Detail name Cause Check method Check result Action Target. Power was switched on for the first time in the absolute position detection system.

Next

Mitsubishi Servo Motor Repair

mitsubishi servo drive manual

Do not supply power to the main circuit power supply terminals L1, L2, L3 of the servo amplifier. Electronic gear numerator Used to set the electronic gear numerator value. Detail Detail name Cause Check method Check result Action Target 92. The lower 2 digits on the display indicate the alarm number that has occurred or the parameter number in error. Detail Detail name Cause Check method Check result Action Target 84.

Next

AC Servos

mitsubishi servo drive manual

Alarm content After the scale measurement encoder was set to the absolute position detection system, the power was switched on for the first time. Continuous flow of a large current may cause a fire. For removal of the front cover, refer to section 1. This function permits ease of gain adjustment of the servo amplifier. When placed in the servo-on status, the servo amplifier is ready to operate and the servo motor is locked. This test will show if there are any shorts or opens in the winding.

Next

AC Servos

mitsubishi servo drive manual

Note 2 with the speed reducer case, do not configure the oil seal. When using a fuse instead of the no-fuse breaker, use the one having the specifications given in this section. Alarm content The linear servo motor seed has exceeded the permissible instantaneous speed. Detail Detail name Cause Check method Check result Action Target 52. Connect the diode in the correct direction.

Next